离心泵是管路系统中的重要动力元件,也是管路系统中主要噪声源之一。在离心泵运行过程中,泵内流动诱导噪声向管路上下游传播。为了更好地了解离心泵诱导流噪声的大小,通过试验测试的方法,基于四端网络测量法,分析在不同流量及不同转速条件下离心泵进出口流噪声的变化规律。研究结果可为工程中离心泵流噪声控制提供参考。 The centrifugal pump is an important power element and one of the main noise sources in pipeline system. During the operation of the centrifugal pump, the flow in the pump induces noise to propagate up and down the pipeline. In order to better understand the magnitude of the induced flow noise of the centrifugal pump, through the test method, based on the fourterminal network measurement method, the change law of the inlet and outlet flow noise of the centrifugal pump is analyzed under different flow rate and different speed conditions. The research results can provide reference for the control of centrifugal pump flow noise in engineering.
离心泵是管路系统中的重要动力元件,也是管路系统中主要噪声源之一。在离心泵运行过程中,泵内流动诱导噪声向管路上下游传播。为了更好地了解离心泵诱导流噪声的大小,通过试验测试的方法,基于四端网络测量法,分析在不同流量及不同转速条件下离心泵进出口流噪声的变化规律。研究结果可为工程中离心泵流噪声控制提供参考。
离心泵,四端网络法,流噪声
Tong Zhang1,2, Yanglei Zhan3, Tianyun Li1,2,4*, Xiang Zhu1,2,4
1School of Naval Architecture and Ocean Engineering, Huazhong University of Science & Technology, Wuhan Hubei
2Hubei Key Laboratory of Naval Architecture & Ocean Engineering Hydrodynamics, Wuhan Hubei
3China Ship Development and Design Center, Wuhan Hubei
4Collaborative Innovation Center for Advanced Ship and Deep-Sea Exploration, Shanghai
Received: Feb. 14th, 2021; accepted: Mar. 9th, 2021; published: Mar. 16th, 2021
The centrifugal pump is an important power element and one of the main noise sources in pipeline system. During the operation of the centrifugal pump, the flow in the pump induces noise to propagate up and down the pipeline. In order to better understand the magnitude of the induced flow noise of the centrifugal pump, through the test method, based on the four-terminal network measurement method, the change law of the inlet and outlet flow noise of the centrifugal pump is analyzed under different flow rate and different speed conditions. The research results can provide reference for the control of centrifugal pump flow noise in engineering.
Keywords:Centrifugal Pump, Four-Terminal Network Method, Flow Noise
Copyright © 2021 by author(s) and Hans Publishers Inc.
This work is licensed under the Creative Commons Attribution International License (CC BY 4.0).
http://creativecommons.org/licenses/by/4.0/
作为重要的流体运输装置及能量转换设备,泵广泛运用于国民经济各部门以及舰船、潜艇、航空航天等领域,其中70%为离心泵 [
国外Simpsont [
本文以工程中某离心泵为例,利用自主搭建流噪声测试台架,基于四端网络法测量离心泵在不同转速、不同流量下进出口诱导流噪声,结合试验结果分析其噪声特性,为后期噪声控制优化提供参考。
离心泵具有一个进口端与出口端,进出口端流体区域间存在声场耦合。由于离心泵流动诱导噪声属于低频噪声,其内流道尺寸远小于声波波长,所以此时的泵声源可以看作为一个点声源或面声源。因此可采用四端网络模型,用进出口端的状态参数及其之间的线性关系来模拟泵声源 [
图1. 四端网络法示意图
图1中,1、2、3、4为声压测点, P i + 和 P i − 为进口管路中方向相反的两列行波, P o + 和 P o − 为出口管路中方向相反的两列行波, P s 为模型泵声源,S为声源矩阵。关系如下所示:
{ P o + P o − } = [ S 11 S 12 S 21 S 22 ] { P i + P i − } + { P o s P i s } (1)
要想获得声源矩阵S,需在无源状态下进行测试,即略去声源 P s 项得:
{ P o + P o − } = [ S 11 S 12 S 21 S 22 ] { P i + P i − } (2)
即:
P o + P i + = S 11 + S 12 P i − P i + (3)
P o − P i + = S 21 + S 22 P i − P i + (4)
令 U = P o + P i + , V = P o − P i + , R = P i − P i + 代入得:
U = S 11 + S 12 R (5)
V = S 21 + S 22 R (6)
由于实验中只能测得4个水听器的声压值,即 P 1 、 P 2 、 P 3 、 P 4 ,而 P i + 、 P i − 、 P o + 、 P o − 可用以下关系式表示:
进口管路:
P 1 = P i + + P i − (7)
P 2 = P i + e − j k s + P i − e j k s (8)
P i + = e j k s p 1 − p 2 e j k s − e − j k s (9)
P i − = − e j k s p 1 + p 2 e j k s − e − j k s (10)
其中s为水听器之间的距离,k为波数。
同理,出口管路:
P 3 = P o + + P o − (11)
P 4 = P o + e − j k s + P o − e j k s (12)
P o + = e j k s p 3 − p 4 e j k s − e − j k s (13)
P o − = − e j k s p 3 + p 4 e j k s − e − j k s (14)
经过无源测试得到声源矩阵S各个参数,之后根据每组有源工况测点测得声压值代入式(1)即得离心泵向进出口端诱导流噪声。
本文试验测试台架如图2所示,试验系统由离心泵、变频电机、测试直管段、挠性接管、两段15 m软管、流量计、流量调节阀、换热器、压力水罐等组成,设备均布置在钢铸平台上,泵组采用弹性安装;通过变频启动器调节电机转速;换热器主要用于系统流体温度的控制,防止长时间运行管路水温度过高;测点水听器采用齐平式安装,这样既能准确地测出信号又能减少流体流动的影响 [
图2. 离心泵流噪声测试台架示意图
图3. 试验台架现场图
离心泵性能参数如表1所示,其轴频 f 1 = n / 60 ≈ 49.2 Hz ,叶频 f B P F = Z f 1 = 295 Hz 。
性能 | 参数 |
---|---|
额定流量(m3/h) | 80 |
设计扬程(m) | 20 |
额定转速n(r/min) | 2950 |
叶片数Z | 6 |
表1. 离心泵性能参数
1) 试验开始前,首先检查循环水管路系统密封性以及各个设备、仪器是否正常;
2) 在泵不运转的条件下,采用换能器作为外加声源,获得两组线性无关的测试状态,用来求解声源矩阵S;
3) 启动变频电机,待循环水管路系统运行稳定后根据不同工况要求改变电机转速(本文取1200 r/min、1800 r/min、2400 r/min及额定转速)以及通过流量调节阀改变流量(本文取20 m3/h、40 m3/h、60 m3/h、80 m3/h、100 m3/h、120 m3/h);
4) 调整到指定工况,在计算机上通过B&KPLUSE软件进行噪声测量及数据处理,本文测试信号频率范围为0~1000 Hz,根据采样定理和工程要求,采样频率为2560 Hz,记录保存数据;
5) 利用声源矩阵S和各工况下测点测得声压得到泵进出口诱导流噪声。
保持电机额定转速2950 r/min不变,在不同流量下,离心泵进出口流噪声如图4~11所示:
图4. 20 m3/h进出口流噪声
图5. 40 m3/h进出口流噪声
图6. 60 m3/h进出口流噪声
图7. 80 m3/h进出口流噪声
图8. 100 m3/h进出口流噪声
图9. 120 m3/h进出口流噪声
图10. 额定转速不同流量下泵进口流噪声
图11. 额定转速不同流量下泵出口流噪声
由图4~9可得:在额定转速不同流量下,离心泵诱导流噪声出口处声压级大于进口处声压级,说明离心泵噪声源主要位于出口处;在不同流量工况下,泵进出口流噪声呈宽频特性,在离心泵轴频(49.2 Hz)、叶频(295 Hz)、二倍轴频(100 Hz)、二倍叶频(590 Hz)、三倍叶频(885 Hz)附近处均存在峰值,且峰值较高,结合文献 [
调节流量阀开度,保持额定流量80 m3/h不变,在不同转速下,离心泵进出口流噪声及各主要谐频分量如图12~15所示:
图12. 额定流量不同转速下泵进口流噪声
图13. 额定流量不同转速下泵出口流噪声
图14. 泵进口各谐频分量流噪声
图15. 泵出口各谐频分量流噪声
由图12、图13可得:在额定流量不同转速下,泵进出口流噪声呈宽频特性,在1200 r/min、1800 r/min、2400 r/min及2950 r/min (额定转速)工况下,其对应的轴频、叶频、倍叶频附近处流噪声均存在峰值高点,且出口处流噪声比入口处较大。通过图14、图15可以看出,进出口各主要谐频分量随着转速增大,流噪声声压级幅值也增大,相邻工况间声压级幅值最大相差20分贝,说明叶轮转速对其流动噪声影响明显,叶片与流体间的相互作用是流噪声的主要来源。此结论与文献 [
本文通过离心泵流噪声测试台架,基于四端网络测试的方法,测量在不同流量与不同转速工况下离心泵进出口的流噪声。得出以下结论:
1) 离心泵诱导流噪声出口处声压级大于进口处声压级,在频域上呈宽频特性,且在轴频、叶频、倍叶频处峰值较高;
2) 在额定流量下,离心泵效率高且噪声低,偏离额定流量时,泵内出现不稳定现象,容易诱导噪声;
3) 离心泵轴转速对进出口流噪声影响显著,随着离心泵转速的增加,其进出口流噪声及主要谐频分量增加,说明叶片与流体间的相互作用是离心泵流噪声的主要来源。
国家自然科学基金资助项目(51839005,51879113);中央高校基本科研业务费资助项目(2019kfyXMBZ048)。
张 桐,詹阳磊,李天匀,朱 翔. 变工况条件下离心泵诱导流噪声试验研究Experimental Research on Induced Flow Noise of Centrifugal Pump under Variable Working Conditions[J]. 声学与振动, 2021, 09(01): 36-45. https://doi.org/10.12677/OJAV.2021.91005